Life Fitness Treadmill 9500HRT User Manual

Life Fitness Model 9500HRT(Rev 1 & 2) & 9500HR Treadmill  
How To... INSTALL THE LIFELINK UPGRADE KIT  
TOOLS REQUIRED: Standard Screwdriver, Phillips Screwdriver, Hex Key Wrench Set, Pliers, Wire Cutters,  
Anti-Static Strap, Small Adjustable Wrench  
WARNING: FAILURE TO OBSERVE SAFETY PROCEDURES WHEN SERVICING THIS UNIT  
COULD RESULT IN INJURY FROM ELECTRICAL SHOCK  
(9500HR ONLY)  
STEP 1:  
Enter into the service menu by pressing manual-9-1-9, enter. Press the fit test program key ( 0001 ) and record the  
total number of times the wax pump has discharged while the unit has been in operation.  
STEP 2:  
Turn the power off at the ON/OFF switch and unplug the unit at the wall outlet.  
STEP 3:  
Ground yourself by positioning an anti-static strap around your wrist and attaching the other end (alligator clip or  
adhesive end) to a bare metal surface on the machine frame.  
(9500HRT REV 2 ONLY)  
STEP 3:  
With the help of another person, tip the treadmill onto its user  
right side. Follow the left side of the frame to the middle. Using a  
standard screwdriver, pop open the three plastic rivets securing  
the control board shelf to the frame. Pull the shelf downward and  
towards you to lower the CONTROL BOARD SHELF on its  
hinges.  
STEP 4:  
Plug the NETWORK HARNESS supplied in the upgrade kit to  
the additional plug connector on the CONTROL BOARD marked  
P7. Route the NETWORK HARNESS along the frame towards  
the front of the unit to the POWER MODULE. Replace the  
CONTROL BOARD SHELF back into its original position.  
(9500HRT REV 1 AND 9500HR ONLY)  
STEP 4:  
Using a Phillips screwdriver, remove the four screws securing the connector cover located under the user left side of  
the DISPLAY CONSOLE. Unplug the 4-PIN and 10-PIN connectors to the DISPLAY CONSOLE.  
STEP 5:  
Using a Phillips screwdriver, remove the eight screws that hold the CONSOLE PAN to the faceplate. Remove the four  
screws securing the Lifepulse assembly and unplug the 7-PIN CONNECTOR and the ground strap. Remove the eight  
screws securing the ELECTRONIC BOARD to the faceplate. Unplug the ribbon and stop switch cables.  
STEP 6:  
NOTE THE ORIENTATION OF E-PROM BY THE U-NOTCH.  
Remove and replace the E-PROM (U1) with the E-PROM supplied  
in the upgrade kit. Return the DISPLAY CONSOLE to its proper  
position by reversing Steps 4 and 5.  
STEP 7:  
With the help of another person, tip the treadmill onto its user right  
side. Follow the left side of the frame to the middle. Using a  
standard screwdriver, pop open the three plastic rivets securing the  
control board shelf to the frame. Pull the shelf downward and  
towards you to lower the CONTROL BOARD SHELF on its hinges  
 
10601 West Belmont Avenue  
Franklin Park, IL 60131  
(800) 351-3737 or (847) 451-0036 / FAX (847) 451-4137  
MO51-00K23-A012  
 

Lenovo Computer Drive 9300 User Manual
Lexmark Copier Color MFP User Manual
Liebherr Ice Maker 7081 411 01 User Manual
Lightolier Indoor Furnishings 1001HCB User Manual
Linksys Stereo System DMP100 User Manual
Logitech Webcam C920 User Manual
Magnavox Stereo System US2 MANT900 User Manual
Memorex CD Player MD6488 User Manual
Memorex CRT Television MT2206 User Manual
Metra Electronics Car Stereo System 99 8714 User Manual