Linear Home Security System DXS 65 User Manual

1. PRODUCT DESCRIPTION  
2. FEATURES  
The Model DXS-65 is a supervised water-resistant emergency alarm transmitter designed for use with Linear’s  
PERS Consoles and can also be used with other Linear DX or DXS format receivers. This transmitter features  
a large, easy to find, HELP button. An optional blank face aqua colored button is included for custom labeling or  
alternate uses. Pressing the button activates the transmitter and sends a digitally coded wireless signal to its  
companion receiver. To insure sending a complete signal, press the transmitter button for a minimum of  
two seconds.  
DXS-65  
OPTIONAL BLANK  
AQUA BUTTON  
BY  
TRANSMIT  
INDICATOR  
DXS-65  
TRANSMITTER  
MOUNTING  
PLATE  
Supervised Emergency  
Alarm Transmitter  
The transmitter can be wall mounted using the integral snap-on mounting bracket, or simply be placed on a table.  
Four rubber “feet” are supplied for table-top use.The DXS-65 is factory set to a unique code, so no field coding is  
required. The transmitter can send a signal for up to 10 seconds per activation. The red operation indicator lights  
when the transmitter is activated.  
An optional supervisory status timer is included in the DXS-65. Status transmissions occur every two hours and  
inform the receiver of the condition of the transmitter and its batteries. The factory setting has the status timer  
disabled. The status timer can be enabled by pressing the HELP button continuously for five seconds. The red  
operation indicator will blink as the status timer is enabled. The status timer can be disabled by removing the  
power from the transmitter. NOTE: If the status timer is required for the installation, be sure to enable it after  
replacing the transmitter’s batteries.  
Installation  
Instructions  
Every two hours the transmitter tests for low batteries. This test takes place even if the status transmissions have  
not been enabled. If the batteries test low, a low battery signal is sent to the receiver.  
Each transmitter is sealed to provide water-resistance.The transmitter is powered by two 2032 “coin-cell” batteries  
and must be disassembled to replace the batteries.  
ACTIVATION  
BUTTON  
Before system testing and operation, each transmitter must be programmed into its receiver. Refer to the receiver’s  
or Console’s instructions for details on programming transmitters into the system. When using a PERS or DVS  
Console, be sure to program the receiver for the correct sensor type and supervision option using the  
RA-2400 programming software. (Note: DVS Consoles default the DXS-65 as an arm/disarm transmitter.)  
MOUNTING  
SCREWS (2)  
TABLE-TOP  
FEET (4)  
USA & Canada (800) 421-1587 & (800) 392-0123  
(760) 438-7000 - Toll Free FAX (800) 468-1340  
3. OPTIONAL WALL MOUNTING  
4. STATUS SUPERVISION OPTION  
5. PROGRAM TRANSMITTER INTO RECEIVER  
ATTACH WALL  
MOUNT BRACKET  
WITH TWO SCREWS  
HOOK TOP OF TRANSMITTER  
ONTO THE BRACKET TABS  
RED INDICATOR  
TO ENABLE THE HOURLY  
WILL BLINK WHEN  
PLACE THE CONSOLE OR RECEIVER  
INTO PROGRAMMING MODE  
1
2
SUPERVISORY STATUS  
STATUS IS ENABLED  
SWING TRANSMITTER  
ONTO BRACKET  
REPORTS, PRESS THE HELP  
BUTTON FOR 5 SECONDS  
ACTIVATE THE TRANSMITTER  
TO PROGRAM IT INTO THE  
CONSOLE OR RECEIVER  
NOTE: THE RED INDICATOR  
WILL NOT LIGHT EACH TIME  
AN AUTOMATIC HOURLY  
STATUS REPORT IS SENT  
NOTE: IF THE TRANSMITTER  
HAS SUPERVISION ENABLED,  
BE SURE TO PROGRAM THE  
CONSOLE WITH THE SENSOR  
OPTION SET AS SUPERVISED  
FOR THIS TRANSMITTER  
IMPORTANT!  
AFTER ENABLING STATUS REPORTS ON THE  
TRANSMITTER, BE SURE TO SET THE SENSOR NUMBER  
IN THE PERS OR DVS CONSOLE TO SUPERVISED USING THE  
RA-2400 PROGRAMMING SOFTWARE  
TO REMOVE  
TRANSMITTER  
PRESS TAB ON  
BRACKET  
FOR NON-WALL MOUNT APPLICATIONS,  
STICK THE FOUR ADHESIVE "FEET"  
ONTO THE MOUNTING BRACKET  
PERS-3600B  
CONSOLE  
6. TESTING TRANSMITTER  
7. BATTERY REPLACEMENT OR BUTTON EXCHANGING  
LINEAR LIMITED WARRANTY  
This Linear product is warranted against defects in material and workmanship for twelve (12) months. This  
warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal  
distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their  
selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part  
of Linear LLC for consequential damages arising out of or in connection with use or performance of this  
product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal,  
installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied  
warranties for fitness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu of all other  
warranties express or implied.  
1
TWIST A COIN OR SCREWDRIVER IN  
THE SLOT ON TOP OF TRANSMITTER  
TO OPEN THE CASE  
PLACE THE CONSOLE OR RECEIVER  
INTO TEST MODE  
1
2
REMOVE THE CASE TOP, BUTTON, SILICONE  
SEAL, AND LIFT OUT THE TRANSMITTER  
CIRCUIT BOARD  
2
ACTIVATE THE TRANSMITTER,  
VERIFY THAT THE SIGNAL WAS  
RECEIVED  
3
REPLACE THE BATTERIES WITH  
TWO TYPE MAXELL CR2032  
200mA HR OR DURACELL DL2032  
COIN-CELL BATTERIES,  
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear  
Technical Services at 1-800-421-1587 for an RPA# and other important details.  
IMPORTANT !!!  
Linear radio controls provide a reliable communications link and fill an important need in portable wireless  
signaling. However, there are some limitations which must be observed.  
PLUS SIDE AWAY FROM THE  
CIRCUIT BOARD  
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15  
devices. As such, they have limited transmitter power and therefore limited range.  
NOTE: TO VERIFY THE RADIO  
RANGE, BE SURE TO TEST  
THE TRANSMITTER FROM THE  
INTENDED MOUNTED OR  
TABLE-TOP LOCATION  
4
• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals  
that occur on or near their operating frequencies, regardless of code settings.  
RE-ASSEMBLE THE UNIT  
BY REVERSING THE STEPS  
Changes or modifications to the device may void FCC compliance.  
• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.  
• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or  
dealer, and these facts should be communicated to the ultimate users.  
5
NOTE: IF THE STATUS TIMER IS REQUIRED  
FOR THE INSTALLATION, BE SURE TO ENABLE  
IT AFTER REPLACING THE BATTERIES  
TEST THE TRANSMITTER  
AFTER RE-ASSEMBLING  
PERS-3600B  
CONSOLE  
TEST SYSTEM WEEKLY!  
Copyright © 2008 Linear LLC  
Issue Date November 4, 2008  
228490 C  
 

Lightolier Indoor Furnishings 1100FTUES User Manual
Lightolier Indoor Furnishings VRA2G16LV2FT User Manual
Linear Barcode Reader AM DPR User Manual
Link electronic Stereo Amplifier DigiFlex 1132 User Manual
Lochinvar Boiler PB 0502M9 User Manual
Lowrance electronic GPS Receiver X102C User Manual
Mackie Musical Instrument D 2 User Manual
Magnavox Blu ray Player DC146 User Manual
McCulloch Lawn Mower 532 43 22 10 User Manual
Metra Electronics Automobile Accessories 99 5500 User Manual